Web Analytics
Gå til innhold
  • Bli medlem

Line6 og BOSS


Lykkjen

Anbefalte innlegg

Har egentlig et lignende spørsmål... Har en Line 6 Vetta og en Boss AC-3. Skulle gjerne koblet Bossen inn i effektloopen på ampen, slik at jeg kan aktivere den fra Line 6 FBV Longboard. Lar dette seg gjøre?

Uten at jeg vet alt for mye om Vettaen så går jeg ut ifra at det ikke er noe særlig problem, noe annet ville ihvertfall jeg synes er rart..

Prøvd å sjekke manualen?

Lenke til kommentar
Del på andre sider

Uten at jeg vet alt for mye om Vettaen så går jeg ut ifra at det ikke er noe særlig problem, noe annet ville ihvertfall jeg synes er rart..

Prøvd å sjekke manualen?

Hvilke kabler må jeg ha? Det funket ikke med jack. Jeg har lest manualen, men fikk ikke så mye ut av det... Har en knapp på FBV Longboard som jeg (slik som jeg har forstått det) er til å aktivere FX Loop...

Lenke til kommentar
Del på andre sider

Hvilke kabler må jeg ha? Det funket ikke med jack. Jeg har lest manualen, men fikk ikke så mye ut av det... Har en knapp på FBV Longboard som jeg (slik som jeg har forstått det) er til å aktivere FX Loop...

Aner faktisk ikke..

Jeg vil tro det skal kobles: FX-send -> Boss -> FX-return.

Hvis det ikke funker så har jeg ikke peiling. Har bare knotet litt med en Vetta i butikken, aldri prøvd den med FBV :P

Lenke til kommentar
Del på andre sider

Dette er forresten det som står i manualen:

The Effects Loop

While we’ve tried to anticipate all of your effects needs, you may still want to use other

effects with Vetta. That’s okay, we won’t be upset. Obviously, if you’ve got actual

physical world stompboxes you want to use, run them in front of Vetta as you would do

with any other amp. If you’ve got rack mount effects or other devices that work at line

level, these can be hooked up in Vetta’s effects loop. This loop is switchable (from the

front panel or from the FBV foot controller), the on/off state is remembered with each

channel that you save, and you can even route the loop either series or parallel (see

‘Routing Post Effects’ on page 4•18).

Analog Effects Loop

To hook something up to Vetta’s loop, you’ll need a pair of what are commonly referred

to as ‘Y’ or ‘insert’ cables. These cables have a 1/4-inch TRS (Tip, Ring, Sleeve) plug

on one end, that splits out to a pair of 1/4-inch TS (Tip, Sleeve) plugs at the other end.

You’ll need one of these for Vetta’s loop send, and one for the return. You hook them up like this:

sdasd.jpg

It’s worth pointing out here that we haven’t hooked these cables up the way you might

use them for an effect ‘insert.’ An effect insert uses these cables to allow input and

output signals to both be connected at the one jack. If Vetta had an effect insert (like

many mixing boards do), you’d jack the TRS end of a single one of these cables in this

insert, then one of the split ends of the cable would go to the effect’s input and the

other would go to the effect’s output. But as the picture shows, we’re not doing that.

Once you’ve got your external effects hooked up, press the LOOP button as needed to

get the loop turned on. Just as with all the other effects, light on, loop on. Light off,

loop goes bye-bye.

Digital Effects Loop

Vetta’s effects loop can also be assigned to either the S/PDIF or AES/EBU digital I/O

for use with outboard effect processors that have the same digital connections.

Page 4 of Output Setup is where you will make these settings. The first parameter is

FORMAT. This is where you set the bit depth and sample rate coming from the Vetta.

Use the soft knob under FORMAT to change this parameter. You have the choice of 16, 20 or 24 bit resolution as well as sample rates of 44.1, 48, 88.2 and 96kHz. It is

wisest to set these parameters for the highest qualities your outboard effect processor

supports and set the processor to lock to the incoming signal from Vetta. Vetta can also

be set to match the bit depth and sample rate of the signal at the digital input. This

means your outboard effect processor can be set to “internal” if you wish. The next

parameter is SOURCE. Use the soft knob to set this to LOOP. The next parameter is

DIG OUT. Simply choose AES/EBU or S/PDIF depending on which format your

outboard effect processor uses. The final parameter is GAIN. If you find that the input

to the effect processor is low, you can boost the gain up to +12dB.

Noen som fikk noe utav det? Det jeg lurer mest på, er om det faktisk er mulig å gjøre dette med en stomp-box. Her står jo bare rack unit nevnt...

Lenke til kommentar
Del på andre sider

Noen som fikk noe utav det? Det jeg lurer mest på, er om det faktisk er mulig å gjøre dette med en stomp-box. Her står jo bare rack unit nevnt...

Orket ikke lese manulen der, men om en effekt er bygget i en snubleboks eller rackkabinett blir uvesentlig for funksjon. Men merk at mange snublebokser er konstruert til å motta en veldig svakt signal direkte fra gitaren din. Effekt ut fra en slik effektsøyfe kan ha veldig høyt linje signal og dermed overstyre inngangen på pedalen. Juster defor effekt send volumet tilsvarende ned.

Lenke til kommentar
Del på andre sider

Opprett en konto eller logg inn for å kommentere

Du må være et medlem for å kunne skrive en kommentar

Opprett konto

Det er enkelt å melde seg inn for å starte en ny konto!

Start en konto

Logg inn

Har du allerede en konto? Logg inn her.

Logg inn nå
  • Hvem er aktive   0 medlemmer

    • Ingen innloggede medlemmer aktive
×
×
  • Opprett ny...

Viktig informasjon

Dette nettstedet bruker cookies for å gi deg en best mulig brukeropplevelse Bruksvilkår.